features nec's l- band sp3t switch description upg2227t5f nec's upg2227t5f is a l-band sp3t gaas fet switch for cdma/pcs/gps triple mode digital cellular telephone application. the device can operate from 500 mhz to 2.5 ghz with low insertion loss and high linearity. applications ? cdma/pcs/gps triple mode digital cellular telephone ? s hort range wireless california eastern laboratories ordering information remark to order evaluation samples, contact your nearby sales of?ce. part number for sample order: u pg 2 227t5f-a caution observe precautions when handling because these devices are sensitive to electrostatic discharge. ? low insertion loss : 0.45 db typ. @ 1.0 ghz 0.50 db typ. @ 2.0 ghz ? high isolation : 21 db typ. @ 1.0 ghz ? high power : p in (0.1 db) = 33.0 dbm typ. @ +2.7 v, 1.0 ghz ? package : 12-pin plastic qfn package (3.0 3.0 0.75 mm) ? p b f ree part number package marking supplying form upg2227t5f-e2-a 12-pin plastic qfn 2227 ? embossed tape 8 mm wide ? pin 1 indicates roll-in direction of tape ? qty 3 kpcs/reel ? pb free
upg2227t5f pin connections truth table (t op v iew) 10 11 12 1 2 3 6 5 4 9 8 7 (bottom v iew) 6 5 4 3 2 1 10 11 12 7 8 9 pin no. pin name 1 v cont1 2 rf1 3 gnd 4 gnd 5 rf2 6 v cont2 7 gnd 8 rf3 9 v cont3 10 gnd 11 ant 12 gnd v cont 1 rf1 gnd gnd ant gnd v cont 3 rf3 gnd gnd rf2 v cont 2 v cont1 v cont2 v cont3 ant-rf1 ant-rf2 ant-rf3 h l l on off off l h l off on off l l h off off on
upg2227t5f upg2227t5f absolute maximum ratings (t a = 25c) parameter symbol ratings unit switch control voltage v cont ? 8.0 to +8.0 v input power p in +36 dbm operating ambient temperature t a ? 45 to +85 c storage temperature t stg ? 55 to +150 c recommended operating range (t a = 25c) parameter symbol min. typ. max. unit switch control voltage (h) v cont(h) +2.4 +2.7 +5.0 v switch control voltage (l) v cont(l) ? 0.2 0 +0.2 v
electrical characteristics (t a = +25 c, v cont = +2.7 v/0 v, z o = 50 , o ff ch ip dc blocking capacitors value = 56 pf, unless otherwise speci?ed) upg2227t5f parameter symbol test conditions min. typ. max. unit insertion loss l ins f = 0.5 to 1.0 ghz ? 0.45 0.60 db f = 1.0 to 2.0 ghz ? 0.50 0.70 db f = 2.0 to 2.5 ghz ? 0.55 ? db isolation isl f = 0.5 to 1.0 ghz 22 26 ? db f = 1.0 to 2.0 ghz 17 21 ? db f = 2.0 to 2.5 ghz ? 20 ? db input return loss rl in f = 0.5 to 2.0 ghz 15 20 ? db f = 2.0 to 2.5 ghz ? 20 ? db output return loss rl out f = 0.5 to 2.0 ghz 15 20 ? db f = 2.0 to 2.5 ghz ? 20 ? db 0.1 db gain compression input power p in (0.1 db) f = 1.0 ghz 31.0 33.0 ? dbm 1 db gain compression input power p in (1 db) f = 1.0 ghz ? 34 ? dbm 2nd harmonics 2f0 f = 1.0 ghz @ p in = +27 dbm 65 75 ? dbc f = 2.0 ghz @ p in = +24 dbm ? 75 ? dbc 3rd harmonics 3f0 f = 1.0 ghz @ p in = +27 dbm 65 75 ? dbc f = 2.0 ghz @ p in = +24 dbm ? 75 ? dbc 3rd order distortion input intercept point iip 3 f = 837 mhz/838 mhz @ 1 mhz spacing p in = +22 dbm each @ 2 tone ? 64 ? dbm f = 1 880 mhz/1 881 mhz @ 1 mhz spacing p in = +21 dbm each @ 2 tone ? 63 ? dbm cross modulation x-mod f = 837 mhz/838 mhz @ 1 mhz spacing p in = +22 dbm each @ 2 tone f = 880 mhz p in = ? 27 dbm ? ? 108 ? dbm f = 1 880 mhz/1 881 mhz @ 1 mhz spacing p in = +21 dbm each @ 2 tone f = 1 960 mhz p in = ? 27 dbm ? ? 110 ? dbm switch control speed t sw ? 150 ? ns switch control current i cont rf non ? 1 20 a
evaluation circuit the application circuits and their parameters are for reference only and are not intended for actual design-ins. upg2227t5f 56 pf v cont 1 1,000 pf 56 pf ant rf2 56 pf rf1 v cont 2 1,000 pf 56 pf rf3 v cont 3 1,000 pf l esd note note recommend attached l esd to antenna port for esd protection.
upg2227t5f package dimensions 12-pin plastic qfn (unit: mm) 3.0 3.0 0.750.1 (bottom v iew) 0.5 1.0 1.550.1 0.40.1 0.9 0.4 0.9 0.4 dimensions of pin no.1 indication 0.5 1.0 0.40.1 0.24 +0.07 -0.0 5 1.550.1 0.40.1 0.40.1
upg2227t5f recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact your nearby sales of?ce. soldering method soldering conditions condition symbol infrared re?ow peak temperature (package surface temperature) : 260 c or below time at peak temperature : 10 seconds or less time at temperature of 220 c or higher : 60 seconds or less preheating time at 120 to 180 c : 120 30 seconds maximum number of re?ow processes : 3 times maximum chlorine content of rosin ?ux (% mass) : 0.2%(wt.) or below ir260 vps peak temperature (package surface temperature) : 215 c or below time at temperature of 200 c or higher : 25 to 40 seconds preheating time at 120 to 150 c : 30 to 60 seconds maximum number of re?ow processes : 3 times maximum chlorine content of rosin ?ux (% mass) : 0.2%(wt.) or below vp215 wave soldering peak temperature (molten solder temperature) : 260 c or below time at peak temperature : 10 seconds or less preheating temperature (package surface temperature) : 120 c or below maximum number of ?ow processes : 1 time maximum chlorine content of rosin ?ux (% mass) : 0.2%(wt.) or below ws260 partial heating peak temperature (pin temperature) : 350 c or below soldering time (per side of device) : 3 seconds or less maximum chlorine content of rosin ?ux (% mass) : 0.2%(wt.) or below hs350 life support applications these nec products are not intended for use in life support devices, appliances, or systems where the malfunction of these prod ucts can reasonably be expected to result in personal injury . the customers of cel using or selling these products for use in such applications do so at their own risk and agree to fully indemnify cel for all damages resulting from such improper use or sale. a business partner of nec compound semiconductor devices, ltd. 05/10/2005 caution do not use different soldering methods together (except for partial heating).
5-8 4590 patrick henry drive santa clara, ca 95054-1817 telephone: (408 ) 9 19-250 0 facsimile : ( 40 8 ) 988-0279 subject: compliance with eu directives cel certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of european union (eu) directive 2002/95/ec restriction on use of hazardous substance s i n electrical and electronic equipment (rohs) and the requirements of eu directive 2003/11/ec restriction on penta and octa bde. cel pb-free products have the same base part number with a suffix added. the suffix Ca indicates that the device is pb-free. the Caz suffix is used to designate devices containing pb which are exempted from the requirement of rohs directive (*). in all cases the devices have pb-free terminals. all devices with these suffixes meet the requirements of the rohs directive. this status is based on cels understanding of the eu directives and knowledge of the materials that go into its products as of the date of disclosure of this information . restricted substanc e per rohs concentration limit per rohs (values are not yet fixed) concentration contained in cel devices -a -a z lead (p b) < 1000 ppm not detected (*) mercury < 1000 ppm not detected cadmiu m < 100 ppm not detected hexavalent chromiu m < 1000 ppm not detected pbb < 1000 ppm not detected pbde < 1000 ppm not detected if you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. important information and disclaimer: informatio n p rovided by ce l o n its website or in other communications concertin g the substan ce content of its products represents knowledge and belief as of the date that it is provided. cel bases its know ledge and belief on informatio n provided by thir d p arties and makes no representation or warrant y as to the accura cy of such information. efforts are underw ay to better integrate information from third parties. cel has taken and continues to take reasonable steps to provide representative and ac curate information but ma y not have conducted destructive testing or chemical analysis on incoming ma terials and chemicals. cel and ce l suppliers consider certain information to be propri etar y, and thus cas numbers and other limited information may not be availabl e for release . in no event shall cels liability arising out of such information exceed the total purchase price of the cel part(s) at issue s old by cel to customer on an annual basis. see cel terms and conditions for additional clarification of wa rranties and liabilit y.
|
